The P0311 OBD-II trouble code means the engine control module has detected a combustion misfire associated with Cylinder 11.

Unlike P0300, which indicates random or multiple-cylinder misfires, P0311 identifies one specific cylinder. That narrows the diagnosis, but it does not prove that the Cylinder 11 ignition coil has failed.

A worn spark plug, weak ignition coil, defective fuel injector, damaged electrical circuit, intake leak, low compression, or valvetrain problem can all trigger P0311.

The computer knows Cylinder 11 contributed less power than expected. It does not know which component should be replaced. Apparently, even a V12 remains stubbornly opposed to convenient assumptions.

P0311 belongs to the misfire-code family covered in the complete Pro Street P-code OBD-II guide.

P0311 Quick Answer

Item	Information
Trouble code	P0311
Definition	Cylinder 11 Misfire Detected
System	Ignition and combustion
Severity	High
Safe to drive?	Only briefly if the engine runs smoothly and the Check Engine Light is not flashing
Most common causes	Spark plug, ignition coil, injector, wiring, intake leak, or low compression
Common applications	V12 and W12 engines
Related codes	P0211, P0361 and P0300
Typical repair range	Approximately $100 to $15,000+, depending on the vehicle and cause

What Does the P0311 Code Mean?

P0311 breaks down as follows:

P: Powertrain
0: Generic OBD-II code
3: Ignition or combustion misfire
11: Cylinder 11

The engine control module monitors slight changes in crankshaft speed during individual combustion events. A properly operating cylinder accelerates the crankshaft when combustion forces its piston downward.

When Cylinder 11 repeatedly produces less power than expected, the crankshaft momentarily slows. The control module recognizes this pattern and stores P0311.

Depending on the severity and frequency of the misfire, the Check Engine Light may remain steadily illuminated or begin flashing.

P0311 identifies the affected cylinder. It does not identify whether the failure involves:

Spark
Fuel delivery
Airflow
Compression
Valve operation
Mechanical timing
Electrical control

For broader information about combustion failures, visit our engine misfire symptoms, causes and diagnosis guide.

Which Vehicles Can Store P0311?

P0311 only applies to engines with at least 11 cylinders.

Common configurations include:

V12 engines
W12 engines
Certain specialty multi-cylinder engines

Applications may include some vehicles from:

Audi
Bentley
Volkswagen
BMW
Mercedes-Benz
Maybach
Aston Martin
Ferrari
Lamborghini
Rolls-Royce

The general P0311 definition remains consistent, but cylinder location, ignition design, fuel-injection system, access procedure, and test specifications vary significantly.

A code reader may identify Cylinder 11 in seconds. Reaching its spark plug on some vehicles may require considerably longer and a suspicious number of removed components.

Where Is Cylinder 11 Located?

Cylinder 11 location depends on the engine family and manufacturer’s numbering system.

On a V12 engine, Cylinder 11 may be:

On either cylinder bank
Near the front or rear of the engine
Beneath an intake manifold
Behind wiring or fuel-system components
In a location requiring extensive disassembly

Some manufacturers place odd-numbered cylinders on one bank and even-numbered cylinders on the opposite bank. Others number the cylinders sequentially along each bank.

W12 engines use an even more complex arrangement that should only be identified using manufacturer-specific service information.

Before removing an ignition coil, spark plug, or injector, identify Cylinder 11 using:

Factory service information
Manufacturer repair manual
Underhood emissions label
Vehicle-specific firing-order diagram
Correct engine identification code

Never assume Cylinder 11 is simply the eleventh coil you can see.

Testing the wrong cylinder wastes diagnostic time and can create an additional misfire if an unrelated connector or coil boot is damaged.

Common Conditions Associated With P0311

A Cylinder 11 combustion problem may cause:

Illuminated Check Engine Light
Flashing Check Engine Light
Rough or unstable idle
Engine shaking
Hesitation
Reduced acceleration
Loss of engine power
Hard starting
Stalling
Increased fuel consumption
Raw fuel smell from the exhaust
Failed emissions test
Popping from the intake or exhaust
Reduced turbocharger boost
Limp mode
Additional ignition, injector, or fuel-trim codes

A single-cylinder misfire may be difficult to feel on a V12 because the remaining cylinders can partially mask the loss of contribution.

The absence of violent shaking does not make P0311 harmless. Unburned fuel can still damage the catalytic converter, contaminate the engine oil, and increase emissions.

How Serious Is P0311?

P0311 should be treated as a high-priority trouble code.

An active misfire may send unburned fuel into the exhaust. That fuel can ignite inside the catalytic converter, causing the catalyst to overheat or melt.

Continued driving may contribute to:

Catalytic converter damage
Oxygen sensor contamination
Cylinder-wall fuel wash
Engine oil dilution
Burned exhaust valves
Piston damage
Excessive engine vibration
Reduced fuel economy
Increased emissions

Stop Driving Immediately If:

The Check Engine Light is flashing
The engine shakes violently
Power loss becomes severe
The vehicle stalls
A strong raw-fuel smell is present
The engine overheats
Mechanical knocking is heard
Abnormal valvetrain noise develops

A flashing Check Engine Light generally indicates a catalyst-damaging misfire. Reduce engine load, pull over safely, and shut off the engine.

If the light remains steady and the engine runs reasonably smoothly, driving a short distance for diagnosis may be possible. Avoid heavy throttle, high RPM, towing, and boost.

Most Common Causes of P0311

Cylinder 11 can misfire because of an ignition, fuel, electrical, airflow, compression, or mechanical problem.

Possible cause	Relative likelihood
Worn or fouled spark plug	Very high
Weak or failed ignition coil	Very high
Damaged coil boot or spark plug wire	High
Clogged or failed fuel injector	High
Coil or injector wiring fault	Medium
Intake leak near Cylinder 11	Medium
Low Cylinder 11 compression	Medium
Oil or coolant in the spark plug well	Application dependent
Carbon buildup on an intake valve	Medium on direct-injected engines
Burned or leaking valve	Medium
Worn camshaft lobe or failed follower	Application dependent
Damaged piston ring	Lower
Head gasket failure	Lower
Incorrect valve timing	Lower
PCM driver failure	Rare

The engine family, mileage, maintenance history, related codes, and freeze-frame conditions should determine the testing order.

How to Diagnose P0311

Step 1: Confirm P0311

Connect an OBD-II scanner and record:

Stored codes
Pending codes
Permanent codes
Freeze-frame data
Cylinder-specific misfire counters

Do not erase P0311 before saving the freeze-frame information.

Record:

Engine RPM
Engine load
Vehicle speed
Coolant temperature
Intake-air temperature
Short-term fuel trim
Long-term fuel trim
Throttle position
Fuel-system status

The operating conditions can provide important clues.

When P0311 occurs	Possible diagnostic direction
Cold start	Injector leak, deposits, coolant intrusion, or weak compression
Warm idle	Intake leak, injector imbalance, or mechanical problem
Heavy acceleration	Weak coil, worn plug, excessive plug gap, or insufficient fuel
Wet weather	Coil boot, connector, or insulation damage
After heat soak	Ignition coil, injector, connector, or wiring fault
Constantly	Dead coil, failed injector, circuit problem, or low compression
After recent service	Loose connector, wrong plug, damaged boot, or installation error

Step 2: Check for Related Trouble Codes

P0311 may appear with other misfire, ignition, injector, or timing codes.

Related codes include:

P0300 — Random or Multiple Cylinder Misfire
P0307 — Cylinder 7 Misfire
P0308 — Cylinder 8 Misfire
P0309 — Cylinder 9 Misfire
P0310 — Cylinder 10 Misfire
P0312 — Cylinder 12 Misfire
P0171 or P0174 — System Too Lean
P0172 or P0175 — System Too Rich
P0211 — Cylinder 11 Injector Circuit Malfunction
P0361 — Ignition Coil K Primary/Secondary Circuit Malfunction
Camshaft or crankshaft position codes
Fuel-pressure codes
Valve-timing codes

Several cylinder-specific misfire codes may indicate a shared problem such as:

Low fuel pressure
Contaminated fuel
Large vacuum leak
MAF sensor error
Incorrect valve timing
Weak charging voltage
Poor engine ground
Shared coil or injector power-supply failure
Crankshaft position signal fault

Step 3: Determine Whether the Fault Is Bank-Specific

A V12 or W12 engine may store P0311 with other codes from the same cylinder bank.

Compare:

Misfire counts across both banks
Bank 1 and Bank 2 fuel trims
Upstream oxygen or air-fuel sensor data
Camshaft timing values
Fuel-rail pressure where separate rails are used
Intake manifold operation
Bank-specific ignition and injector power supplies

If several cylinders on the same bank misfire, the underlying problem may involve:

Bank-specific intake leak
Camshaft timing error
Fuel-rail pressure problem
Oxygen sensor bias
Shared wiring or ground
Intake-runner control fault
Exhaust restriction

P0311 alone points toward Cylinder 11. P0311 combined with several same-bank faults deserves a wider diagnostic view.

Step 4: Verify Cylinder 11 Location

Use vehicle-specific service information to identify Cylinder 11.

Inspect the surrounding area for:

Disconnected coil or injector connectors
Loose connector terminals
Oil inside the spark plug well
Coolant contamination
Damaged wiring
Rodent damage
Cracked vacuum hoses
Intake manifold leaks
Wiring contacting hot components
Loose engine grounds

Access may require removal of:

Engine covers
Intake ducts
Air boxes
Fuel rails
Intake manifold components
Cowl or bracing components

Confirm the correct procedure before beginning major disassembly.

Step 5: Inspect the Cylinder 11 Spark Plug

Remove the Cylinder 11 spark plug and compare it with a plug from a healthy cylinder.

Check for:

Worn electrodes
Excessive gap
Cracked porcelain
Carbon fouling
Oil contamination
Wet fuel deposits
Coolant deposits
Overheating
Incorrect heat range
Wrong plug type
Improper torque

A fuel-wet plug may indicate that fuel is entering Cylinder 11 but the mixture is not igniting.

A dry plug may suggest inadequate fuel delivery.

Oil deposits may indicate:

Worn piston rings
Valve-guide problems
PCV-system problems
Leaking spark plug tube seal
Oil entering the plug well

If the plugs are beyond their service interval, replace the complete set with the correct type and gap.

On a V12, replacing the full set may involve substantial labor. That still does not justify skipping diagnosis and replacing every ignition component within visual range.

Step 6: Swap the Cylinder 11 Ignition Coil

If the engine uses accessible coil-on-plug ignition, move the Cylinder 11 coil to another cylinder.

For example, swap the Cylinder 11 and Cylinder 9 coils. Clear the codes and operate the engine under conditions similar to those recorded in the freeze-frame data.

If the code changes from:

P0311 to P0309

the ignition coil is likely defective.

If P0311 returns on Cylinder 11, the coil probably is not the cause.

Inspect the coil and boot for:

Carbon tracking
Cracks
Moisture
Oil contamination
Coolant contamination
Corroded contacts
Burned internal springs
Damaged insulation

Review our bad ignition coil guide for additional ignition-system information.

Also see our ignition coil replacement guide before installing replacement components.

If moving the coil requires major disassembly, determine whether electrical testing offers a more practical first step.

Step 7: Understand P0311 Versus P0361

P0311 and P0361 describe related but different faults.

Code	Meaning
P0311	The PCM detected a combustion misfire associated with Cylinder 11
P0361	The PCM detected an electrical malfunction involving Ignition Coil K’s primary or secondary circuit

P0361 provides stronger evidence of an ignition-coil circuit problem.

Possible P0361 causes include:

Failed ignition coil
Missing coil power
Open trigger circuit
Trigger circuit shorted to ground
Trigger circuit shorted to voltage
Loose connector terminal
Corroded connector
Damaged wiring
Failed PCM coil driver

P0311 without P0361 may still be ignition-related, but fuel delivery, airflow, compression, and valve operation must also be tested.

Coil letters frequently correspond with cylinder numbers, but manufacturer information should be checked before assuming Coil K controls Cylinder 11.

Step 8: Test the Cylinder 11 Fuel Injector

A clogged, leaking, stuck, electrically open, or unpowered injector can cause P0311.

Listen to the Cylinder 11 injector with a mechanic’s stethoscope and compare it with the other injectors.

Further testing may include:

Injector resistance measurement
Injector voltage test
Noid-light test
Injector current-ramp test
Injector balance test
Fuel-pressure drop test
Injector swap test where practical

Use manufacturer specifications for injector resistance and circuit testing.

Pro Street injector-testing resources include:

Never open a gasoline direct-injection fuel system without following the manufacturer’s pressure-relief procedure.

Step 9: Understand P0311 Versus P0211

P0211 identifies an electrical fault involving the Cylinder 11 injector circuit.

Code	Meaning
P0311	Cylinder 11 combustion misfire
P0211	Cylinder 11 injector circuit malfunction

If P0311 and P0211 appear together, concentrate on:

Injector power supply
Injector control circuit
Connector condition
Terminal tension
Injector resistance
Wiring performance under load
PCM injector driver

P0211 does not automatically prove that the injector has failed. Damaged wiring or a loose connector can prevent a functional injector from operating.

Step 10: Inspect the Coil and Injector Circuits

If the ignition coil and injector test correctly, inspect their circuits.

Check for:

Correct supply voltage
Reliable ground
Ignition-coil trigger signal
Injector control pulse
Loose terminal tension
Corroded connector pins
High circuit resistance
Wiring shorted to ground
Wiring shorted to voltage
Heat-damaged insulation
Poor engine or PCM grounds

Use voltage-drop testing while the circuit is operating whenever possible.

A circuit can show continuity and still fail under load. Electricity remains annoyingly unwilling to certify a wire merely because the multimeter beeped once.

PCM failure is possible but uncommon. Verify the component, wiring, voltage supply, grounds, and mechanical condition first.

Step 11: Check for an Intake Leak

An intake leak near the Cylinder 11 runner can create a localized lean condition.

Inspect:

Intake manifold gasket
Cylinder 11 injector seal
Vacuum hoses
PCV system
Brake-booster hose
Intake manifold
Throttle-body gasket
Intake-runner control hardware

A smoke test is generally the safest and most effective way to locate an intake-system leak.

Compare fuel trims between the two cylinder banks. A significantly more positive correction on Cylinder 11’s bank may support a bank-specific air or fuel-delivery problem.

Step 12: Check Bank-Specific Fuel Delivery

Some V12 and W12 engines use separate fuel rails, pressure sensors, pumps, or control circuits for different portions of the engine.

Review:

Commanded and actual fuel-rail pressure
Low-pressure fuel supply
Bank-specific fuel trims
Injector balance
Pump duty cycle
Fuel-pressure sensor data
Fuel quality

A bank-specific fuel-pressure problem can make Cylinder 11 appear to be the primary fault while affecting several cylinders to a lesser degree.

Step 13: Perform a Compression Test

If Cylinder 11 has spark, fuel, and correct electrical control, test its compression.

Compare Cylinder 11 with the remaining cylinders and use manufacturer specifications for minimum pressure and allowable variation.

Low compression may be caused by:

Burned intake valve
Burned exhaust valve
Bent valve
Worn piston rings
Damaged piston
Broken valve spring
Failed follower or lifter
Worn camshaft lobe
Head gasket failure
Cylinder-wall damage
Incorrect valve timing

If Cylinder 11 compression is low, continue with a cylinder leak-down test.

Step 14: Perform a Cylinder Leak-Down Test

Position Cylinder 11 at top dead center on its compression stroke and introduce regulated compressed air.

Air heard or observed at	Likely fault
Throttle body or intake	Leaking intake valve
Exhaust outlet	Leaking exhaust valve
Oil filler opening	Piston rings or cylinder damage
Cooling system	Head gasket, cylinder head, or block damage
Adjacent cylinder	Head gasket failure between cylinders

Leak-down testing helps determine whether P0311 originates from internal engine damage.

Step 15: Inspect Cylinder 11 Valve Operation

If compression is low or valvetrain noise is present, inspect valve movement.

Depending on the engine, testing may require:

Removing the valve cover
Comparing rocker-arm or follower movement
Measuring valve lift
Inspecting valve springs
Checking lifters or followers
Verifying engine oil pressure
Inspecting the camshaft
Checking the oil filter for metal debris

Reduced valve movement may indicate a failed follower, broken valve spring, collapsed lifter, or worn camshaft lobe.

Step 16: Check for Intake-Valve Deposits

Direct-injected engines can develop deposits on their intake valves because fuel no longer flows across the back of each valve.

Uneven deposits near Cylinder 11 may cause:

Cold-start P0311
Rough idle
Airflow imbalance
Misfire that improves after warm-up

A borescope inspection can help confirm deposits. Approved cleaning procedures may include media blasting or professional chemical cleaning.

Step 17: Clear P0311 and Verify the Repair

After repairing the confirmed fault:

Clear stored and pending codes.
Start the engine.
Verify a stable idle.
Monitor Cylinder 11 misfire counters.
Recreate the original freeze-frame conditions when safe.
Complete the required drive cycle.
Scan for pending codes.
Confirm that readiness monitors complete normally.

The repair is confirmed when Cylinder 11 misfire counts remain normal and P0311 does not return.

Common P0311 Repairs and Costs

Repair costs can be high on V12 and W12 engines because component access may require considerable disassembly.

Repair	Approximate installed cost
Replace spark plugs	$300–$2,500
Replace one ignition coil	$150–$1,200
Replace coil boot	$100–$500
Clean or replace one injector	$400–$3,000
Repair wiring or connector	$200–$1,500
Repair intake or vacuum leak	$300–$3,000
Intake-valve carbon cleaning	$1,000–$5,000
Replace intake manifold gasket	$1,500–$6,000
Replace failed follower or camshaft	$3,000–$15,000+
Cylinder-head or valve repair	$5,000–$20,000+
Engine replacement	$15,000–$75,000+

These are broad estimates. Vehicle design, parts availability, labor rate, and component access can change the final cost considerably.

The failed component may cost less than the collection of brackets, hoses, wiring, and intake parts placed in front of it.

Common P0311 Diagnostic Mistakes

Replacing Coil 11 Without Testing It

Swap the coil with another cylinder when practical. If the fault follows, replace the coil. If P0311 remains, continue testing.

Testing the Wrong Cylinder

Cylinder numbering varies between V12 and W12 engines. Confirm Cylinder 11 before disassembly.

Confusing P0311 With P0361

P0311 identifies a combustion misfire. P0361 identifies an electrical fault involving Ignition Coil K’s circuit.

Ignoring P0211

P0311 combined with P0211 points toward the Cylinder 11 injector or its circuit and should change the diagnostic priority.

Ignoring Same-Bank Codes

Several codes on the same bank may indicate a shared intake, fuel-delivery, timing, wiring, or exhaust problem.

Replacing the Injector Without Testing It

Confirm injector power, control, resistance, and fuel delivery before replacement.

Clearing Freeze-Frame Data Too Early

Freeze-frame information may be the best evidence of the conditions that triggered P0311.

Skipping Compression Testing

If ignition and fuel tests pass, verify the mechanical condition of Cylinder 11.

Replacing the Catalytic Converter First

The catalytic converter may have been damaged by P0311. Repair the misfire before evaluating catalyst performance.

P0311 Frequently Asked Questions

Does P0311 Mean Ignition Coil 11 Is Bad?

No. A failed coil is common, but P0311 may also result from a spark plug, injector, wiring, intake leak, compression problem, or valvetrain failure.

Can P0361 Cause P0311?

Yes. P0361 identifies an electrical malfunction involving Ignition Coil K, which commonly corresponds with Cylinder 11. Verify the manufacturer’s coil assignment first.

Can P0211 Cause P0311?

Yes. A Cylinder 11 injector-circuit failure can prevent the cylinder from receiving the correct amount of fuel.

Can a Spark Plug Cause P0311?

Yes. A worn, cracked, fouled, overheated, or incorrectly gapped Cylinder 11 spark plug can trigger P0311.

Can a Fuel Injector Cause P0311?

Yes. A clogged, leaking, stuck, electrically failed, or unpowered Cylinder 11 injector can create a cylinder-specific misfire.

Can an Intake Leak Affect Only Cylinder 11?

Yes. An intake manifold or injector-seal leak near the Cylinder 11 runner may create a localized lean condition.

Can a Bank-Specific Fuel Problem Trigger P0311?

Yes. Separate fuel rails, pumps, pressure sensors, or control circuits may cause several cylinders on one bank to run incorrectly, with Cylinder 11 recording the highest misfire count.

Can Low Compression Cause P0311?

Yes. Burned valves, worn rings, piston damage, valvetrain faults, or head gasket failure can reduce Cylinder 11 compression.

Why Does P0311 Only Appear Under Acceleration?

A weak coil, worn plug, excessive plug gap, restricted injector, or fuel-pressure problem may only become noticeable as engine load increases.

Can I Drive With P0311?

Only briefly if the engine runs smoothly and the Check Engine Light remains steady. Stop driving if the light flashes, the engine shakes severely, power drops, or raw fuel can be smelled.

Can P0311 Damage the Catalytic Converter?

Yes. Unburned fuel can overheat and destroy the catalytic converter.

Will P0311 Clear Itself?

The Check Engine Light may turn off after several successful drive cycles, but stored or permanent code data may remain until the required self-tests are completed.

Related Misfire, Injector and Ignition Codes

P0300 — Random or Multiple Cylinder Misfire
P0307 — Cylinder 7 Misfire
P0308 — Cylinder 8 Misfire
P0309 — Cylinder 9 Misfire
P0310 — Cylinder 10 Misfire
P0311 — Cylinder 11 Misfire
P0312 — Cylinder 12 Misfire
P0211 — Cylinder 11 Injector Circuit Malfunction
P0361 — Ignition Coil K Primary/Secondary Circuit Malfunction

Explore the Pro Street OBD-II Code Libraries

Use the Pro Street cornerstone pages to find additional diagnostic trouble codes:

P0311 identifies a combustion misfire associated with Cylinder 11. Save the freeze-frame information and verify the correct cylinder before removing components.

Inspect the spark plug, swap-test the ignition coil where practical, and test the injector and related circuits. If P0311 remains, inspect for intake leaks, bank-specific fuel problems, low compression, and abnormal valve operation.

The correct repair is the one supported by testing—not the component with the most impressive packaging.

P0311 Code: Cylinder 11 Misfire Diagnostic Procedure