If you’re replacing the stereo or adding a subwoofer to a Hyundai Kona, check the model year and factory audio package before you buy a harness. On some Konas the speakers connect to the radio. On others, the receiver feeds a separate amplifier. A plug that fits is only half the battle.
This guide covers both U.S. gas-powered Kona generations. Start with your generation, then match the radio part number and connector to the chart. Kona Electric owners should use the EV-specific radio and amplifier schematics for their model year.
First-generation Hyundai Kona stereo wiring (2018–2023, OS)
The first U.S. Hyundai Kona arrived for 2018. Over its first generation, the factory radio options included standard receivers and navigation-equipped units. If you’re shopping for a 2018–2023 Hyundai Kona stereo harness, check the original radio label and whether your car has a factory amplifier before ordering.
For a standard system, start with the speaker outputs at the radio if its connector matches the chart. For a factory-amplified system, check the amp connector and decide whether you’re retaining the factory amplifier or adding equipment downstream of it. iDatalink lists a specific amp-replacement application for the 2018–2020 Kona with Infinity audio. Check later years and other premium systems separately.
Standard radio factory pinout
These pin numbers come from the first-generation Radio/MP3 connector chart. Confirm the connector designation and the radio variant before tapping any wire. Factory insulation colors for this connector still need exact year and trim verification.
| Circuit | Factory radio cavity |
|---|---|
| Constant battery feeds | B10, B11 |
| Accessory feed | B22 |
| Power grounds | B12, B13 |
| Illumination + / − | B6 / B19 |
| Antenna power | B5 |
| Steering-wheel audio signal / ground | A12 / A26 |
| Left front speaker + / − | A13 / A14 |
| Right front speaker + / − | A16 / A15 |
| Left rear speaker + / − | A1 / A2 |
| Right rear speaker + / − | A28 / A27 |
The Radio/MP3 diagram also lists camera power at A6, video at A7, camera power ground at A20 and video ground at A21. Confirm your camera configuration and supply voltage before connecting a retention interface. If you need help reading the cavity numbers, see how to read a car stereo connector.
Factory external amplifier pinout
This chart applies to the first-generation external-amp configuration shown in the AVN service section. Here, A and B refer to the amplifier connectors. Match the amplifier part number and connector faces before using the chart.
| Circuit | Factory amp cavity |
|---|---|
| Battery feeds | A1–A4 |
| Grounds | A16–A19 |
| Accessory | A8 |
| SPDIF high / low / ground | A20 / A21 / A22 |
| Left front door + / − | A12 / A13 |
| Left front tweeter + / − | A25 / A26 |
| Right front tweeter + / − | A27 / A28 |
| Left rear door + / − | B1 / B2 |
| Right rear door + / − | B3 / B4 |
| Subwoofer + / − | B16 / B17 |
| Center speaker + / − | B18 / B19 |
The service listing uses ambiguous labels for another right-front pair, so confirm that channel from the circuit diagram before wiring it. The SPDIF pins carry digital audio. Connect a speaker-level input at a verified speaker output.
Second-generation Hyundai Kona stereo wiring (2024–2027, SX2)
The redesigned U.S. Kona arrived for 2024 with a 12.3-inch infotainment display. Hyundai offered an eight-speaker Bose system in selected trims. A 12.3-inch screen alone doesn’t tell you what audio package the car has, so verify the trim and amplifier before choosing parts.
For a second-generation Kona speaker upgrade, start at the connector for the speaker you’re replacing. If you’re adding a subwoofer to a Bose-equipped Kona, identify the amp’s subwoofer output and verify that its signal is compatible with your equipment. For a standard-audio car, verify the speaker-level source on its own schematic.
Bose amplifier speaker wire color reference
The following cavities and colors are reported for a 28-pin Bose amplifier application in a 2024–2026 reference. The exact connector ID, model year and trim applicability still need independent factory confirmation. Use the table to compare against the factory schematic for your vehicle before probing or splicing. The 2027 factory pinouts, standard-audio pinouts, and Kona Electric wiring remain unverified here.
| Reported output | Amp pins + / − | Reported wire colors + / − |
|---|---|---|
| Front left tweeter | 1 / 16 | White and black |
| Front right tweeter | 2 / 17 | Red and green |
| Rear left speaker | 12 / 25 | Purple/yellow and purple/brown |
| Rear right speaker | 13 / 26 | Purple/orange and purple/gray |
| Center speaker | 14 / 27 | Purple/blue and purple/orange |
| Subwoofer | 3 / 18 | Purple/brown and purple/yellow |
The color before a slash is the main insulation and the color after it is the stripe. Confirm channel and polarity at the connector you plan to use. The reference also repeats the front tweeter cavities for the front speakers, so the front-door wiring is unverified here.
Adding bass while keeping the factory screen
If you’re comparing compact powered subs, Pro Street Online lists the Rockville RW10CA and the Pyle 10-inch low-profile powered subwoofer. Check space, mounting and signal compatibility for your Kona before choosing either.
For another example of how factory amplifier packages change the wiring, see our Kia Soul stereo wiring guide. Before putting the dash back together, test all four speaker positions, then check the backup camera and steering-wheel controls. If the new radio powers up but stays silent, first verify the factory amp is receiving the signal and turn-on it expects.










