Home Uncategorized Subaru Crosstrek Stereo Wiring Diagram: Radio Pinouts and Harman Kardon Guide

Subaru Crosstrek Stereo Wiring Diagram: Radio Pinouts and Harman Kardon Guide

0

Before you order a harness for your Subaru Crosstrek, check which factory radio is in the dash and whether the car has a separate amplifier. Those two details determine which plugs you need and where to look for a speaker signal. A wire color at the radio can change before it reaches the door. The colors printed on a replacement harness are another thing entirely.

This guide covers U.S.-market XV Crosstrek and Crosstrek models. Match the model year, factory equipment and connector before using any chart. In factory color descriptions, the first color is the main insulation and the second is the stripe.

Model years Start here
2013–2014 XV Crosstrek Identify the non-navigation 20-pin radio or the navigation setup. Note which display shows the backup camera.
2015–2017 XV Crosstrek / Crosstrek Identify the radio and camera connections by model year. Check hybrid applications separately.
2018–2023 Crosstrek Identify the display, factory amplifier and hybrid status. See the radio-side and adapter charts below.
2024–2026 Crosstrek Identify the display and audio package before selecting a harness or tapping speaker wiring.

First generation (2013–2017) β€” XV Crosstrek and Crosstrek stereo wiring

If you’re searching for an XV Crosstrek radio wiring diagram, you’re in the right section. Subaru also sold first-generation U.S. models under the Crosstrek name, so both names belong here. For a stereo swap, start by identifying the original radio and where the factory backup camera displays its picture.

On a 2013–2014 model with the non-navigation radio, the 20-pin plug is the starting point for radio power and the four speaker channels. A navigation-equipped car or a later first-generation radio calls for a closer look at the connectors. Take a photo before you order anything. It’s easier to compare plugs at your desk than with half the dash on the passenger seat.

Early XV Crosstrek 20-pin radio connector (i85)

The factory colors below come from the U.S. XV audio diagram WI-37814. Use them on a matching early non-navigation i85 setup. The 20-pin connector is listed for 2013–2014 non-navigation cars. Check the vehicle against the chart before repairing a cut harness, especially on a 2014. Identify cavities by their molded numbers or connector documentation, since the terminal face and wire side are mirror images.

Circuit Pin Factory color Typical aftermarket lead
Constant 12 V 20 Blue/red Yellow
Switched accessory 12 V 3 Yellow/red Red
Ground 10 Black/blue Black
Illumination + 1 Violet Orange or orange/white
Factory dimmer circuit 2 Black/white Often absent on adapter
Antenna booster feed 9 Yellow/black Blue or blue/white
Left front + / βˆ’ 8 / 7 Blue/orange and white/black White and white/black
Right front + / βˆ’ 18 / 17 Brown/yellow and green Gray and gray/black
Left rear + / βˆ’ 6 / 5 White/red and red/black Green and green/black
Right rear + / βˆ’ 16 / 15 Gray/green and red/white Violet and violet/black

2015–2017 Crosstrek 10-pin and 6-pin radio connectors

The 2015–2016 Crosstrek uses the Toyota-style 10-pin and 6-pin radio connectors. Certain early Fujitsu Ten navigation units also use that connector style. Match the radio part number and camera setup before applying a pinout. For 2015–2017 cars with the 7-inch display, iDatalink documents a separate Maestro installation application. Check the interface fitment for your exact year and equipment.

The service diagrams show the same factory colors on the 10-pin i85 and 6-pin i131 connectors for 2016 hybrid and non-hybrid Crosstreks without telematics and the 2017 Crosstrek 2.0L Premium without telematics. The diagrams depict both audio and navigation receivers. Compare the labels and plug shapes before using the chart. The first-generation 20-pin i85 plug above uses different pin numbers.

Circuit Connector and pin Factory wire color
Constant 12 V i85 pin 4 Blue/red
Switched accessory 12 V i85 pin 3 Yellow/red
Ground i85 pin 7 Black/blue
Antenna control i85 pin 8 Yellow/black
Illumination + i85 pin 10 Violet
Illumination βˆ’ i131 pin 5 Black/white
Left front + / βˆ’ i85 pins 2 / 6 Blue/orange and white/green
Right front + / βˆ’ i85 pins 1 / 5 Brown/yellow and green
Left rear + / βˆ’ i131 pins 2 / 6 White/red and red/black
Right rear + / βˆ’ i131 pins 1 / 3 Gray/green and red/white

The left-front negative wire in these diagrams is white/green at the radio and white/black farther downstream. Check the circuit at the connector you’re working on. The 2017 Premium telematics diagrams show different front wiring at the radio. Use the schematic for the exact telematics configuration before tapping its speaker wires.

Second generation (2018–2023) β€” Crosstrek radio wiring and Harman Kardon

For a second-generation Subaru Crosstrek stereo install, write down the screen size and check whether the car has the Harman Kardon amplifier. An 8-inch display alone doesn’t identify the audio package. That distinction matters when you’re choosing a harness or tracking down why a replacement radio powers up without sound.

If you’re keeping the factory amp, check that the radio interface supports that configuration. If you’re replacing the amp or adding a subwoofer, figure out which connector carries the signal you need before looking up speaker wire colors. Use the factory radio chart for its listed configuration and the adapter chart when you’re wiring the corresponding aftermarket harness. Hybrid models need a separate fitment check.

Factory radio power and speaker circuits

These radio-side circuits are from the non-hybrid 6.2-inch diagram with EyeSight (AUDIO(6ES)-01) and the 7-inch diagram without EyeSight (AUDIO(70E)-01). Connector A is i85 and connector B is i131. Speaker rows list the two legs in cavity order. Verify polarity for the vehicle before splicing.

Circuit Radio cavity Factory wire
Battery feed A4 Blue/red
Accessory feed A3 Yellow/red
Audio bracket ground circuit A7 Black/blue
Antenna circuit A8 Yellow/black
Left front audio pair A6 / A2 White/black and blue/orange
Right front audio pair A1 / A5 Brown/yellow and green
Left rear audio pair B2 / B6 White/red and red/black
Right rear audio pair B1 / B3 Gray/green and red/white

Crosstrek Hybrid factory speaker wiring

The second-generation HEV service diagram WI-48072 shows these four speaker pairs at the radio. Match the i85 and i131 connectors and the wiring section for your car before using this chart. The rows list wire colors in cavity order.

Channel Factory radio connector and cavities Factory colors
Left front i85 pins 2 and 6 Blue/orange and white/black
Right front i85 pins 1 and 5 Brown/yellow and green
Left rear i131 pins 2 and 6 White/red and red/black
Right rear i131 pins 1 and 3 Gray/green and red/white

Maestro SU3 adapter wiring

The following colors are on the Maestro SU3 T-harness in its 2018–2023 Crosstrek installation guide. Check that your exact radio and amplifier package are supported before ordering. With the factory amp present, follow the amplified routing in the adapter instructions.

Circuit Adapter lead
Constant 12 V Yellow
Accessory 12 V Red
Ground Black
Illumination Orange
Amplifier turn-on Blue/white
Power antenna Blue
Reverse trigger Purple/white
Parking brake input Light green
Vehicle speed signal Pink
Left front + / βˆ’ White / white-black
Right front + / βˆ’ Gray / gray-black
Left rear + / βˆ’ Green / green-black
Right rear + / βˆ’ Purple / purple-black

Harman Kardon amplifier wiring

Decide whether you’re keeping the factory amplifier, replacing it or adding a sub. That decision determines which side of the amplifier you work from. For supported 2018–2021 Crosstrek applications, the Maestro DSR1 installation guide locates the amp under the passenger seat and maps the following aTO2 adapter leads to speaker channels. Check the actual equipment and harness revision before using this map. Subaru service bulletin 15-214-17 lists factory Harman Kardon amplifier 86221FL010 and its superseding part 86221FL011 for the Crosstrek. Check the label or parts catalog by VIN to identify the amp in your car. Use the factory schematic if you need original wire colors or amplifier connector cavity numbers.

Speaker output Positive adapter lead Negative adapter lead
Right front Blue, input 5 Blue/black
Left front Orange, input 6 Orange/black
Subwoofer 1 White, input 7 White/red
Subwoofer 2 Gray, input 8 Gray/red
Right rear Green, input 9 Green/red
Left rear Purple, input 10 Purple/red
Right tweeter Blue, input 11 Blue/red
Left tweeter Orange, input 12 Orange/red

Third generation (2024–2026) β€” Crosstrek stereo wiring and display options

On the third-generation Crosstrek, identify the factory screen and audio package before mapping out an upgrade. Crutchfield’s 2024 fitment listings account for both the 11.6-inch display and whether the car has Harman Kardon. When buying parts for a 2025 or 2026 model, look up that exact year and match the equipment installed in the car.

Figure out what you’re changing before pulling trim. A speaker swap starts at the speaker connector. Adding an amplifier while keeping the factory screen starts with deciding where to pick up the audio signal. If you’re considering a radio replacement, check which factory features the interface can retain before you order any parts.

2024–2026 speaker connector fitment

The speaker-end plugs give you a way to replace speakers without cutting the harness. AutoHarnessHouse lists these adapters for the corresponding factory equipment. Confirm the connector at the speaker before ordering.

Speaker location Factory system Plug-in adapter
Front and rear doors Standard or Harman Kardon AHH-4400
Front tweeters, where fitted Standard AHH-4447
Dash speakers Harman Kardon AHH-4431

Subaru service bulletins identify Harman amplifier assembly 86221FN01A for certain 2024 and 2025 Crosstrek applications. Check the label on the amp against the parts information for your VIN. For radio or amp rewiring, confirm the connector cavities and wire colors against the schematic for the exact trim and audio package. Those factory pinouts and colors remain unconfirmed here.

Before you connect the new radio

  1. Record the model year, radio part number, display type, factory amp and hybrid status.
  2. Photograph the connectors and match the cavity numbering to the wiring diagram.
  3. Confirm what the adapter retains, including the steering-wheel controls, backup camera and factory amp where equipped.
  4. Match the radio harness and adapter by circuit function. Keep each speaker’s positive and negative leads paired.
  5. Test audio at each speaker, fade and balance, the camera and steering-wheel controls before putting the dash back together.

Why does my new Crosstrek stereo turn on with no sound?

If the original system has a separate amp, check whether the interface supports it and whether the amp is turning on. Also check that you used the input path specified for the amplified system.

Can I use the same wire colors at the radio and at the door?

Identify the wire at the connector where you plan to work. A circuit can change color through an intermediate connector, and an adapter uses its own color scheme.

LEAVE A REPLY

This site uses Akismet to reduce spam. Learn how your comment data is processed.