If your OBD-II scanner displays B0057, your vehicle has detected that the driver seat belt pretensioner deployment loop resistance is lower than the manufacturer expects. This diagnostic trouble code (DTC) indicates a potentially serious fault within the Supplemental Restraint System (SRS) that could prevent the driver’s seat belt pretensioner from operating correctly during a collision.

Seat belt pretensioners work alongside airbags to improve occupant safety. During a crash, the Airbag Control Module (ACM) commands the pretensioner to instantly tighten the driver’s seat belt before the airbag deploys. If the ACM detects abnormally low resistance in the pretensioner’s firing circuit, it stores B0057 and illuminates the Airbag Warning Light.

This guide explains what the B0057 code means, its symptoms, common causes, repair costs, and how technicians diagnose and repair the issue.

Quick Facts

Item	Information
OBD-II Code	B0057
Description	Driver Seat Belt Pretensioner Deployment Loop Resistance Low (Subfault)
Category	Body (B)
System	Supplemental Restraint System (SRS)
Severity	★★★★★ (Critical)
Safe to Drive?	Mechanically yes, safety-wise no
Repair Difficulty	Moderate
Typical Repair Cost	$150–$1,200

What Does B0057 Mean?

The B0057 diagnostic trouble code indicates the Airbag Control Module has detected lower-than-expected resistance within the driver seat belt pretensioner deployment loop.

Every pretensioner contains a pyrotechnic firing circuit with a very specific resistance value. The ACM continuously monitors that circuit to verify it’s capable of deploying correctly during a crash.

When resistance drops below specification, the ACM assumes there’s a fault such as:

Shorted wiring
Internal pretensioner failure
Damaged connector
Short to ground
Moisture contamination

To prevent accidental deployment or unreliable operation, the ACM disables the affected pretensioner and stores B0057.

Symptoms of B0057

Common symptoms include:

Airbag warning light illuminated
“Service Airbag” message
SRS warning light
Stored B0057 code
Driver restraint system warning
Additional SRS fault codes
No engine performance problems

Most drivers notice no difference during everyday driving because pretensioners activate only during a collision.

Common Causes

1. Shorted Driver Pretensioner Circuit

The most common cause is a short within the pretensioner firing circuit that reduces resistance below specification.

2. Damaged Wiring

Under-seat wiring can become:

Pinched
Chafed
Melted
Crushed

Any of these conditions may allow wires to contact each other and lower circuit resistance.

3. Water Intrusion

Moisture beneath the driver’s seat can:

Corrode terminals
Create unintended electrical paths
Lower measured resistance

4. Damaged Connector

A partially damaged connector may create a low-resistance condition by allowing conductors to contact one another.

5. Failed Pretensioner

Internal electrical failure within the pretensioner assembly itself can also reduce deployment loop resistance.

6. Airbag Control Module Failure

Although uncommon, a defective ACM can incorrectly interpret resistance values.

How Serious Is B0057?

Extremely serious.

The ACM cannot guarantee proper pretensioner deployment when resistance is below specification.

As a result:

Driver restraint performance is reduced.
Airbag timing may be affected.
Crash protection may not meet manufacturer specifications.

Immediate diagnosis is recommended.

Can You Drive With B0057?

Mechanically, yes.

From a safety standpoint, no.

Driving with an active SRS fault means your driver’s restraint system may not provide full protection during a collision.

How to Diagnose B0057

Step 1: Scan the Airbag Module

Use a professional scan tool capable of accessing:

Supplemental Restraint System
Airbag Control Module
Body Control Module

Generic code readers typically cannot access body (B) codes.

Step 2: Inspect Driver Seat Wiring

Inspect the wiring beneath the driver’s seat for:

Pinched wires
Chafed insulation
Crushed harnesses
Exposed conductors

These issues commonly create low-resistance faults.

Step 3: Inspect Connectors

Check the yellow SRS connectors for:

Bent terminals
Moisture
Corrosion
Damage
Loose locking tabs

Step 4: Measure Circuit Resistance

Following manufacturer service information, verify deployment loop resistance.

Never use a powered test light or jumper wire on any SRS circuit.

Step 5: Inspect the Pretensioner

Check for:

Previous deployment
Internal damage
Retractor issues
Signs of overheating

Replace the pretensioner if testing indicates internal failure.

Common Repair Solutions

Repair	Estimated Cost
Repair damaged wiring	$150–350
Replace connector	$100–250
Replace driver pretensioner	$350–900
Replace seat harness	$300–700
Replace Airbag Control Module	$900–2,000

Common Diagnostic Mistakes

A frequent mistake is replacing the pretensioner before checking the wiring harness.

Many B0057 repairs ultimately involve:

Pinched wires beneath the seat
Shorted wiring
Moisture-damaged connectors
Damaged harness insulation

Proper circuit testing should always be performed before replacing expensive SRS components.

Vehicles That Commonly Experience B0057

B0057 may appear on:

Chevrolet Silverado
GMC Sierra
Chevrolet Tahoe
GMC Yukon
Cadillac Escalade
Ford F-150
Ford Explorer
Toyota Camry
Toyota Tacoma
Honda Accord
Honda Civic
Acura TLX
Nissan Altima
Hyundai Sonata
Kia K5

Manufacturer-specific definitions may vary slightly.

How to Prevent B0057

Although not every failure is preventable, you can reduce the risk by:

Keeping under-seat wiring protected
Avoiding pinched harnesses
Keeping carpets dry
Disconnecting the battery before removing seats
Using OEM replacement parts
Repairing SRS warning lights promptly

Frequently Asked Questions

What causes B0057?

The most common causes include shorted wiring, damaged connectors, failed pretensioners, water intrusion, or Airbag Control Module failure.

What does “Resistance Low” mean?

It means the ACM detected less electrical resistance than expected within the pretensioner deployment loop, usually indicating a short circuit or internal component failure.

Is B0057 dangerous?

Yes.

The driver’s seat belt pretensioner may not operate correctly during a collision, reducing occupant protection.

Can I clear B0057?

Yes, but unless the electrical fault is repaired, the code will return during the next SRS self-test.

Does B0057 require replacing the pretensioner?

Not always.

Many repairs involve damaged wiring or connectors rather than replacing the pretensioner itself.

Will B0057 affect vehicle performance?

No.

The code affects only the Supplemental Restraint System and does not impact engine, transmission, or braking performance.

Final Thoughts

The B0057 code indicates that the driver seat belt pretensioner deployment loop resistance is lower than factory specifications, signaling a fault that could prevent the pretensioner from functioning correctly during a collision. Although the vehicle may drive normally, the driver’s restraint system may not provide the level of protection it was designed to deliver.

Most B0057 repairs involve correcting damaged wiring, replacing faulty connectors, or installing a new pretensioner when necessary. A thorough diagnosis using manufacturer-approved procedures is the safest and most effective way to restore full SRS functionality.

Continue expanding your SRS diagnostic library:

B0057 Code Explained: Driver Seat Belt Pretensioner Deployment Loop Resistance Low (Subfault)